1 bag with 10 pieces brass M2.5 screw nut to glue.
The screw nuts has 4.5 mm diameter and it is 6 mm long. The threaded hole inside is 4 mm long.
This screw nuts is for artist without kiln.
ATTENSION: THIS SCREW NUT TYPE IS ONLY FOR GLUE! PLEASE DON'T TRY TO MELT IT INTO GLASS!
USAGE:
I suggest to use 4 mm normal bead mandrel with bead release or 5 mm mandrel with thin bead release.
Create your bead on the end of the mandrel. The mandrel must be minimum 6 mm inside the bead. After your bead is cold down, clean the hole from bead release.
I suggest to use fast dry (5 minutes) epoxy glue. Use a toothpick to put the glue into the hole and cover the hole surface with glue. Screw the brass nut on M2.5 mandrel or any M2.5 threaded rod and push it into the hole. Be sure that the screw has a contact with the glue and the position of the screw is ok. Screw out the mandrel if the glue is already fix.
Discount prices:
From 2 bags 6.00 EUR/bag
From 10 bags 5.00 EUR/bag
Data Protection
Delivery
Terms and conditions
M2.5 Screw for Lampwork cabochons
Beach Buggy is a interchangeable pendant, screw-on system for lampwork bead jewelry. All metal elements are made from surgical steel (stainless steel), a material of many virtues. Surgical steel is one of the hardest kinds of steel, it does not get worn, does not get colorized and does not induce allergic reactions. It makes the elements long-lasting, they can be assembled and disassembled multiple times. The steel is so hard that you can even use pliers to gently hold and turn the elements without scratching them. You can hold the steel lampwork bead pins into the flame of a lampwork touch and melt glass onto it. All elements are threaded they can be connected by screwing. The lampwork bead pin and the various connector elements provide virtually unlimited possibilities to create fantastic jewelry. The diameter of the lampwork bead pins are 1.1 mm and the various silicon tubes and converters provide a tight fit for beads with holes of a diameter of 2-3 mm. The system is not recommended for holes with a diameter larger than 3 mm as the size of the end elements (4-5 mm) are too small for such beads. The recommended bore diameter is 1.5-2.5 mm.
Reference: 230414
Made from stainless steel and has an overall length of approximately 26 cm. Approximately 6mm diameter hollow handle. The gripping end of the holder is designed like half a clothes pin that pinches the glass rod as it sits in a V shaped trough. For glass rod between 2-10mm.
Reference: 230000-4mm-closed
1 bag with 10 pieces steel M2.5 (closed on the top) screw nut for sunset blvd interchangeable pendant, ring tops. thread size: M2.5 Length: 4mm, you can find in my shop 6mm long too.
Reference: 230271
Zoe pliers Loop forming pliers. Maximum 0.7 mm wire. I SUGGEST TO USE WITH Zoe earrings!
Reference: 230000-6mm
1 bag with 10 pieces steel M2.5 screw nut for sunset blvd interchangeable pendant, ring tops.Length: 6mm, you can find in my shop 4mm long too.
Reference: 230210
lampwork tool - 1 piece heart steel cabochon plate with M2.5mm cabochon mandrel. thread size: M2.5 Size: 40mmx40mm, 3mm thickness Non-round cabochons generally have a definite “up” and “down” end so for my Beach Buggy stainless steel interchangeable system I have created a pendant that lets you to rotate the cabochon by 90 degrees to get the right...
Reference: 230200
Cabochon mandrel with M2.5mm thread. Mandrel has both ends M2.5 threads. (4mm and 6mm) thread size: M2.5 Mandrel is 20 cm long and it has 5mm diameter. Buy pendant: CLICK! Buy screw nuts 4mm: CLICK! Buy screw nuts 6mm: CLICK! Material: Surgical steel WITHOUT SCREW NUTS!
Reference: 230256
10 pieces steel M2.5 screw 8 mm long. thread size: M2.5Length: 8mm, head diameter 3.5mm You should hold the the head with pliers until screw. From 50 pieces we offer 10% discount!From 100 pieces we offer 20% discount!
Reference: 230209
lampwork tool - 1 piece triangle steel cabochon plate with M2.5mm cabochon mandrel. thread size: M2.5 Size: each side is 50mm long, 3mm thickness Non-round cabochons generally have a definite “up” and “down” end so for my Beach Buggy stainless steel interchangeable system I have created a pendant that lets you to rotate the cabochon by 90 degrees to get...
Reference: 230418
1 piece round steel cabochon plate with M2.5mm cabochon mandrel. Size: 40 mm diameter You can create with this caboczon tops for pillbox. Buy pillbox: CLICK! WITHOUT MANDREL AND SCREW NUTS!
Reference: 230204
1 piece square steel cabochon plate with M2.5mm cabochon mandrel. thread size: M2.5 Size: 40mmx40mm, 3mm thickness Non-round cabochons generally have a definite “up” and “down” end so for my Beach Buggy stainless steel interchangeable system I have created a pendant that lets you to rotate the cabochon by 90 degrees to get the right heading. Buy pendant:...
Reference: 230000-4mm
1 bag with 10 pieces steel M2.5 screw nut for sunset blvd interchangeable pendant, ring tops. thread size: M2.5 Length: 4mm, you can find in my shop 6mm long too.
Reference: 230202
1 piece square steel cabochon plate with M2.5mm cabochon mandrel. Size: 30mmx30mm, 3mm thickness Non-round cabochons generally have a definite “up” and “down” end so for my Beach Buggy stainless steel interchangeable system I have created a pendant that lets you to rotate the cabochon by 90 degrees to get the right heading. Buy pendant: CLICK! Buy...
Reference: 230206
lampwork tool - 1 piece rectangle steel cabochon plate with M2.5mm cabochon mandrel. thread size: M2.5 Size: 45mmx30mm, 3mm thickness Non-round cabochons generally have a definite “up” and “down” end so for my Beach Buggy stainless steel interchangeable system I have created a pendant that lets you to rotate the cabochon by 90 degrees to get the right...
Reference: 230203
1 piece square steel cabochon plate with M2.5mm cabochon mandrel. thread size: M2.5 Size: 35mmx35mm, 3mm thickness Non-round cabochons generally have a definite “up” and “down” end so for my Beach Buggy stainless steel interchangeable system I have created a pendant that lets you to rotate the cabochon by 90 degrees to get the right heading. Buy pendant:...
Reference: 230207
1 piece triangle steel cabochon plate with M2.5mm cabochon mandrel. Size: each side is 30mm long, 3mm thickness Non-round cabochons generally have a definite “up” and “down” end so for my Beach Buggy stainless steel interchangeable system I have created a pendant that lets you to rotate the cabochon by 90 degrees to get the right heading. Buy pendant:...
Reference: 230208
lampwork tool - 1 piece triangle steel cabochon plate with M2.5mm cabochon mandrel. thread size: M2.5 Size: each side is 40mm long, 3mm thickness Non-round cabochons generally have a definite “up” and “down” end so for my Beach Buggy stainless steel interchangeable system I have created a pendant that lets you to rotate the cabochon by 90 degrees to get...
1 bag with 10 pieces brass M2.5 screw nut to glue.
The screw nuts has 4.5 mm diameter and it is 6 mm long. The threaded hole inside is 4 mm long.
This screw nuts is for artist without kiln.
ATTENSION: THIS SCREW NUT TYPE IS ONLY FOR GLUE! PLEASE DON'T TRY TO MELT IT INTO GLASS!
USAGE:
I suggest to use 4 mm normal bead mandrel with bead release or 5 mm mandrel with thin bead release.
Create your bead on the end of the mandrel. The mandrel must be minimum 6 mm inside the bead. After your bead is cold down, clean the hole from bead release.
I suggest to use fast dry (5 minutes) epoxy glue. Use a toothpick to put the glue into the hole and cover the hole surface with glue. Screw the brass nut on M2.5 mandrel or any M2.5 threaded rod and push it into the hole. Be sure that the screw has a contact with the glue and the position of the screw is ok. Screw out the mandrel if the glue is already fix.
Discount prices:
From 2 bags 6.00 EUR/bag
From 10 bags 5.00 EUR/bag
